How to maintain and repair the three-legged stainless steel centrifuge
Dichlorophenylphosphine Basic Information Phenylphosphonium dichloride,Diphenylphosphine chloride,Phenylphosphinic acid,2-hydroxyethylphenylphosphinic acid,Phenylphosphonic dichloride,Phenylthiophosphonochloride ShanDong YingLang Chemical Co.,LTD , https://www.sdylhgtrade.com
2. After the machine has been used for six months, it must be carefully inspected and maintained once and recorded. The main maintenance contents are as follows:
1. After the lubrication parts are carefully cleaned, replace the grease, (No. 3 molybdenum disulfide lithium grease). The main lubrication parts of the machine include the upper and lower bearings of the main shaft, the clutch bearing, the spherical washer of the pendulum and the flat head shaft of the brake device;
2. Whether the bearing is damaged or excessively worn, and whether the inner and outer rings are loose with the shaft and the shell;
3. Whether the friction plates of the brake device and the clutch are worn, and whether the V-belt is worn or elongated;
4. Whether the gaskets are aging or deteriorated, causing leakage;
5. Whether the pendulum, spring, and spherical washer are damaged or stuck;
6. Whether the connecting parts are loose or corroded, and whether the lining layer is broken;
7. Whether the drum is deformed or corroded, especially the corrosion condition of the longitudinal weld. If there is obvious thinning of the weld or black honeycomb microporous structure, there is obvious crack at the interface between the weld and the base metal, the knocking weld has no Metal sound and other phenomena should be stopped immediately. For the shackles of the Xing 鸾夯蛩芰 瘸牟愕淖 模 ??? ??? ??? ??? ??? 觳槌牟阕 觳槌牟阕 ? . . . . . . . . . . . . . . . . . ?Basic?BR> Third, according to the inspection results, decided to clean, replace or repair. If the drum is severely deformed or corroded, and the rotating parts are seriously worn, overhaul or replacement should be carried out, and emergency measures such as surface repair welding should not be used.
4. Turning is the main working part of the centrifuge. It belongs to the high-speed rotating parts. After the strict dynamic balance and part-loading inspection in the manufacturing process, the longitudinal welding seams of the drums are all X-ray flawed. In the course of use, in addition to close å— æµ”æ¹«å· . ? ? ? 醋 醋 辉 辉 辉 辉 辉 辉 辉 辉 辉 辉 纳 纳 纳 纳 纳 纳 纳 纳 æžž æžž æžž æžž æžž æžž æžž æžž æžž æžž æžž æžž æžž æžž æžž æžž10. é› é› è¹²?? ç³» æ…µ æ…µ?? 煨奘 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊 膊?ç‹»? BR> V. The integrity of the centrifuge should be guaranteed. It is not allowed to dismantle, change the parts, or add additional accessories.
Sixth, the main components disassembly and adjustment methods:
1. Remove the outer casing, the main shaft shield, the spindle nut and the washer, etc. by using the drum combination. Use the two disassembly screw holes on the upper end of the drum bottom to press the bottom plate of the self-made dismantling tool on the bottom end surface of the drum with two screws. Pull out the screw tightly and push the bottom of the drum out of the main shaft. If the fit is tight due to the corrosion of the tapered hole, the wooden surface can be evenly tapped on the bottom surface, and the rotating drum can be discharged by the screw.
2. After the brake device removes the drum, the brake ring can be seen. Loosen the connecting screw on the brake handle sleeve to remove the brake handle, remove the flat head shaft and the brake pin, and then remove the brake ring. Remove the worn brake band and rive the new brake band with aluminum rivets.
3. Spindle components and clutches For centrifuges with smaller diameters, the clutch is typically mounted under the motor. When disassembling, first loosen the cover and the shaft end retaining ring, pull the clutch out from the motor shaft end with the puller, and then force the drive shaft to clean or replace the clutch and bearing separately. Remove the connecting screw between the bearing housing and the chassis, and then lift the main bearing component together with the driven pulley from above the chassis. After pulling out the pulley, remove the upper and lower bearing caps, and then take the spindle together with the bearing from the bearing. Lift the seat and clean or replace the inner cavity of the bearing housing and the bearing.
For centrifuges with a diameter of more than 1 m, the centrifugal clutch is usually mounted at the lower end of the main shaft. In the same manner as above, it can be lifted from the top of the chassis together with the main bearing components. The clutch cover and the shaft end retaining ring are removed, and the clutch is used to pull the clutch as a whole. The human main shaft is pulled out, and then the starting wheel is forced out by the sleeve, and the centrifugal block and the bearing can be cleaned or replaced separately.
3, the adjustment method of the uneven chassis 4, if there is lifting equipment can lift the chassis, otherwise the hydraulic jack can be supported on the bottom surface of the chassis (near the three ears), evenly press the top chassis to pull out the lower end of the pendulum The swing pin, depending on the unevenness, determines the thickness of the washer between the ball washer and the chassis lug, and inserts an additional washer and swing pin to reset the chassis.
Product Name: Dichlorophenylphosphine
CAS: 644-97-3
MF: C6H5Cl2P
MW: 178.98
EINECS: 211-425-8
Mol File: 644-97-3.mol
Dichlorophenylphosphine Chemical Properties
Melting point: −51 °C(lit.)
Boiling point: 222 °C759 mm Hg(lit.)
Density: 1.319 g/mL at 25 °C(lit.)
Fp: >230 °F
Storage temp. :Store below +30°C.
Form: Liquid
Specific Gravity: 1.319 (20℃)
Color: Clear colorless to slightly yellow
Sensitive: Moisture Sensitive